Design + fabrication · Miami, Florida

Custom electrical, electronics & networking enclosures

Custom housings built around your components, connections, installation, and service access. We can help design the enclosure, check a physical prototype, and fabricate the required quantity.

Your project, in practical terms

From requirement to finished part.

Here’s how we can bring design, fabrication, and delivery together around your needs.

Can you design and make 20 electrical enclosures if I have the electronics but no CAD?

We can develop the CAD and fabricate a small batch of custom plastic electrical enclosures around your electronics. Removable lids, cable-gland openings, board standoffs, gasket interfaces, and M2–M8 heat-set inserts are options we can incorporate into suitable thermoplastic constructions. We can make an initial unit for component fit and service-access review before producing the approved batch for shipment anywhere in the United States.

Where we start. Send component drawings or measurements, connector locations, the mounting arrangement, and quantity. Photos or a sample shipped by arrangement can help establish missing dimensions. Tell us the operating temperature, exposure, and any required enclosure rating so the construction and verification can be scoped.

Can you make a custom rack enclosure for networking equipment that does not fit a standard case?

We can design a networking enclosure or rack-mount assembly around nonstandard equipment, including 1U/2U layouts, custom rack ears, removable panels, ventilation openings, and cable access. Sheet panels or printed components can accommodate the device geometry; we select materials and supports around weight, heat, and mounting span. One unit or a repeat batch can begin with a fit review, followed by fabrication and nationwide shipping.

Where we start. Send the equipment outline, rack dimensions, mounting-hole pattern, connector projections, and cable bend requirements. We can develop the enclosure drawings and review installation remotely; thermal performance and any electrical or fire requirements need to be defined for the complete assembly.

Tell us about your requirements →

Applications & construction options

Built around your use.

Explore materials, dimensions, and details for each application. Use these dimensions as starting points. We develop the final construction and confirm specifications with you around your requirements.

01

Plastic electrical enclosures

Custom boxes, covers, terminal housings, and mounting panels fitted to the electrical components and installation space.

Materials & fabrication
Printed PETG, ASA, ABS, or PC housings; CNC-routed polycarbonate covers and aluminum mounting plates. Flame-retardant grades can be specified where the electrical design requires documented material performance.
Dimensions & construction
Starting configurations include 2–4 mm printed walls and 1/16–1/4 in sheet panels. Heat-set inserts from M2 to M8, plus comparable imperial sizes, can provide reusable threads in suitable thermoplastic bosses. M3/M4 suit compact cover connections; M5–M8 can accommodate larger cover, bracket, or mounting connections with locally enlarged bosses and reinforcement. Add board standoffs, gland openings, gasket grooves, and screw-fastened service covers around the actual components.
What determines the choice
Size wire-bending space and electrical clearances from the hardware and governing requirements. Review continuous and peak internal temperature, ventilation versus sealing, grounding of metal parts, and access for maintenance; material ratings do not certify the assembled enclosure.
02

Networking equipment enclosures

Housings and mounting arrangements for networking devices, gateways, adapters, and small equipment assemblies.

Materials & fabrication
Printed ASA or PETG for device cradles and low-volume shells; CNC-routed plastic or aluminum panels for rack and cabinet installations. Metal may help shield electronics but can obstruct wireless antennas.
Dimensions & construction
Design around a device outline or rack layout, including 1U/2U concepts, rack-ear patterns, connector projections, and cable bend radii. Candidate panel thicknesses are 1/8–1/4 in; lighter sheet construction can use folds or stiffeners.
What determines the choice
Check airflow around switches, routers, gateways, and power supplies; reserve space for RJ45 boots, SFP modules, fiber bend radius, and reset access. Separate RF-transparent antenna areas from shielding, and check temperature with the equipment operating.
03

PCB & embedded-computer housings

Cases with board supports, connector openings, removable covers, and access to storage or controls.

Materials & fabrication
Printed PETG, ABS, ASA, or PC shells with brass inserts; machined acetal or polycarbonate components where flatness and detailed interfaces matter. ESD-dissipative grades can be considered when a defined resistance range is needed.
Dimensions & construction
Starting walls of 2–3 mm, M2.5/M3 board mounts, removable lids, recessed connector faces, and pockets for fans or heat sinks. Model both board surfaces, solder protrusions, SD-card travel, and USB plug envelopes.
What determines the choice
Establish component keep-outs, fastener engagement, electrical isolation, and cooling paths. Check the real board against the first enclosure; nominal board dimensions alone do not capture tall components, revised connectors, or assembly access.
04

Sensor & IoT enclosures

Application-specific housings with mounting features, cable paths, and access for sensor interfaces.

Materials & fabrication
ASA housings for suitable outdoor installations, PC or nylon candidates for mechanically demanding interfaces, and aluminum bodies when a metal construction fits the sensing and communications requirements.
Dimensions & construction
Printed shells can start at 2–4 mm walls with sensor apertures, cable-gland bosses, replaceable mounting tabs, O-ring or gasket interfaces, and serviceable battery compartments. Mounting-hole spacing follows the host equipment.
What determines the choice
Design for rain direction, condensation, UV, antenna placement, sensing path, and maintenance. A sealed box can trap heat or moisture; gasket compression, vent choice, and completed-assembly ingress testing must match the required protection level.
05

Handheld control housings

Control-pendant and instrument cases with button layouts, display openings, grip geometry, and service access.

Materials & fabrication
Printed ABS, ASA, PC, or nylon housings with optional TPU grip pads and bumpers. CNC-cut faceplates can carry displays, buttons, and engraved legends.
Dimensions & construction
Develop full-size grip studies with 2–3 mm shell concepts, screw bosses, trigger or button clearances, cable retention, and a replaceable front panel. Handle shape and balance follow the hand position, gloves, and attached cable.
What determines the choice
Review drop exposure, hand oils, cleaners, button force, screen viewing angle, seam placement, and repeated opening. We select recesses and bumper thickness around likely contact points; a mockup can check ergonomics before functional hardware is fitted.
06

Custom faceplates & connector panels

Panels with precisely located cutouts, legends, mounting holes, and interfaces for existing equipment.

Materials & fabrication
CNC-routed polycarbonate or aluminum panels, laser-cut acrylic for appropriate indoor applications, and engraved laminate overlays. Legends may be surface engraved, reverse engraved, or mechanically recessed with optional paint fill.
Dimensions & construction
Candidate sheet thicknesses span 1/16–1/4 in. Include connector cutouts, keyed flats, countersinks, mounting holes, threaded hardware, and a layout matched to the connector’s maximum panel thickness.
What determines the choice
Verify the nut engagement and rear clearance of every control, connector, and switch. Panel stiffness, edge finish, electrical bonding, abrasion, and the exact cleaner determine whether exposed engraving, an overlay, or protected rear marking is appropriate.

Design is part of the engagement

Help defining it.
Help making it.

We can build the geometry around your hardware, define how the enclosure opens and fastens, and use an initial physical version to check component fit, wiring space, and assembly. Existing CAD can also be adapted for a different process or installation.

Design and documentation can stand alone, continue through our fabrication work, or support production by a specialist facility.

How design assistance works →

Material & process direction

Choose for the application.

  • PETG, ABS, ASA, nylon, or PC filament candidates
  • Acrylic and other suitable sheet plastics for panels and covers
  • Aluminum panels and specialist metal housings as scoped

These are starting points for selection. We confirm the exact grade, thickness, finish, availability, and production route for your project.

Material details & selection →

A useful starting brief

What to send us.

Component drawings or samples, overall envelope, connector locations, mounting arrangement, environment, quantity, and any required ratings.

Send what you have. We can help identify and develop the missing information.

Start a project brief ↗

Related solutions

The adjacent details matter.

A complete solution may combine several of these applications.

Your next useful step

Bring the application. We’ll help develop the solution.

Tell us what must work, what already exists, and the quantity you need. Technical and project conversations are available in English and Spanish.

Tell us what must work