Design + fabrication · Miami, Florida

Custom inspection aids & test fixtures

Fixtures that make a check easier to position, repeat, and interpret. We can help develop the physical interfaces for your inspection or test method and build the supporting hardware.

Applications & construction options

Built around your use.

Explore materials, dimensions, and details for each application. Use these dimensions as starting points. We develop the final construction and confirm specifications with you around your requirements.

01

Go/no-go checking aids

Check a defined feature against an agreed acceptance condition.

Materials & fabrication
Machined acetal or aluminum gauge bodies with hardened contact pins or bushings where wear matters. Printed versions can check ergonomics and access before a controlled checking aid is made.
Dimensions & construction
Define separate go and no-go features from the part tolerance, including allowance for gauge manufacture and wear. Handheld plate concepts may use 1/4–1/2 in stock with handles and unambiguous orientation.
What determines the choice
Agree on the measured feature, permissible insertion force, temperature, reference method, and calibration interval. The gauge needs a documented decision rule; its nominal dimensions should not simply duplicate the part’s maximum and minimum without review.
02

Dimensional comparison templates

Compare a profile, spacing, or assembly arrangement to a physical reference.

Materials & fabrication
Laser-cut acrylic for visual comparisons, CNC-routed polycarbonate for impact-exposed handling, or machined aluminum for durable profile references. Engraved witness lines can identify the comparison surfaces.
Dimensions & construction
Candidate sheet thicknesses of 1/16–1/4 in with datum edges, viewing windows, hole references, and clear revision markings. Thicker stock may be appropriate where the checking edge must resist flex.
What determines the choice
Define whether the tool is a visual aid or an acceptance gauge. Kerf, corner radius, edge quality, parallax, and wear can change the reading; specify the controlled profile and verification method.
03

Camera inspection nests

Hold a part at a repeatable location and angle for an existing imaging system.

Materials & fabrication
Machined acetal or aluminum nests, printed trial inserts, and replaceable pads selected to suit part finish and camera lighting. Matte finishes can be evaluated against specular surfaces.
Dimensions & construction
Add repeatable locating surfaces, stops, keyed orientation, fixture-to-machine datums, and openings for backlighting. Height and tilt at the feature under inspection matter more than the overall tray dimensions.
What determines the choice
Validate focus, glare, shadows, contamination, and part-position variation using the real camera and lighting. Control how the part seats so that a loading error is not interpreted as a product defect.
04

Connector test fixtures

Locate the device and mating connectors with access for the specified test equipment.

Materials & fabrication
Machined insulating plastic bodies with purchased test connectors or pogo-pin modules; aluminum baseplates can provide structure where electrical isolation is separately maintained.
Dimensions & construction
Define pin pitch, insertion depth, connector keys, travel stops, spring load, and replaceable wear modules from the actual connector data. 1/4–1/2 in baseplate concepts can carry toggle or lever mechanisms.
What determines the choice
Check mating force, cycle life, contact access, electrical clearances, ESD requirements, and cable restraint. The fixture provides the mechanical interface; test voltages, circuitry, and electrical safety must be defined with the test-system owner.
05

Instrument holders

Support probes, indicators, cameras, or other instruments in a consistent relationship to the work.

Materials & fabrication
CNC-machined aluminum or acetal holders with standard clamps, threaded inserts, and compatible soft pads. Printed holders can establish reach and alignment for low-load work.
Dimensions & construction
Include split clamps, micrometer or indicator mounting features, 1/4-20 or metric interfaces, height adjustment, and positive locking. Rod diameters and clamp bores follow the purchased instrument or support system.
What determines the choice
Identify probe contact force, vibration, thermal movement, and permissible deflection at the measurement point. Support stiffness and clamping repeatability can dominate the instrument’s nominal accuracy.
06

Product test stands

Provide a repeatable setup for a defined fit, movement, or functional check.

Materials & fabrication
Aluminum frames or plates, machined nests, and replaceable plastic contact parts. Printed components can support a trial setup before repeated-use construction is selected.
Dimensions & construction
Define travel, stops, load introduction, mounting pitch, and access for force or displacement sensors. A benchtop assembly may use 1/4–3/4 in plates and purchased linear guides, with dimensions derived from the test article. Compatible solid plates or blocks can use tapped mounting grids and adjustment connections, including M6–M18 where appropriate to the hardware. Define thread engagement and material section from the test loads.
What determines the choice
Establish load, speed, cycle count, guarding, failure containment, and the reference measurement method. Build around a written test procedure so fixture motion or operator technique does not become an uncontrolled variable.
07

Leak-test mounting fixtures

Hold an assembly and its test connections consistently during a leak check.

Materials & fabrication
Machined aluminum or engineering-plastic supports with purchased test fittings and seals rated for the specified service.
Dimensions & construction
Define locating surfaces, seal compression, port access, clamping, and repeat connection geometry.
What determines the choice
Establish pressure, medium, stored energy, test method, and isolation requirements. Fixture sealing must be distinguished from the product leakage being measured.
08

Electrical programming nests

Locate devices against programming contacts for repeat access.

Materials & fabrication
Machined insulating bodies, printed fit trials, and purchased pogo-pin or connector modules on a stable base.
Dimensions & construction
Match contact pitch, stroke, orientation keys, support points, and board keep-outs to the device.
What determines the choice
Review contact force, ESD control, wear, electrical isolation, and wrong-way loading. Provide replaceable contact modules and access for troubleshooting.
09

Endurance-test supports

Hold parts for repeated motion or loading under a defined procedure.

Materials & fabrication
Aluminum frames, machined fixtures, purchased motion hardware, and replaceable contact parts.
Dimensions & construction
Define travel limits, load introduction, adjustment, sensor access, and specimen replacement.
What determines the choice
Specify cycle count, load, speed, heat buildup, failure containment, and measurement method. The fixture should not introduce an unintended failure mode.
10

Optical alignment fixtures

Position optics, cameras, lights, or targets relative to agreed references.

Materials & fabrication
Machined aluminum or acetal supports with selected surface finishes and purchased adjustment hardware.
Dimensions & construction
Define optical-axis height, adjustment range, aperture clearances, mounting pitch, and positive locking.
What determines the choice
Check vibration, thermal drift, reflections, and sensitivity to clamping. Alignment stability must match the optical task, not simply nominal machining accuracy.
11

Sample preparation holders

Locate specimens during cutting, polishing, sectioning, or other preparation.

Materials & fabrication
Machined metal or compatible engineering plastics with replaceable liners and secure clamps.
Dimensions & construction
Define specimen support, working exposure, tool clearance, coolant drainage, and removal access.
What determines the choice
Review cutting force, heat, chemistry, contamination, and the feature that must remain undisturbed. Protect specimen identity through preparation.

Design is part of the engagement

Help defining it.
Help making it.

We start with the characteristic you need to check, then work backward to the references, access, and fixture geometry. A trial setup can reveal whether loading variation or fixture movement is affecting the result.

Design and documentation can stand alone, continue through our fabrication work, or support production by a specialist facility.

How design assistance works →

Material & process direction

Choose for the application.

  • Printed engineering plastics and CNC-machined plastics
  • Aluminum, fasteners, bushings, and purchased instrument mounts
  • Replaceable contact pads selected for the part surface

These are starting points for selection. We confirm the exact grade, thickness, finish, availability, and production route for your project.

Material details & selection →

A useful starting brief

What to send us.

The feature or function being checked, acceptable variation, parts or drawings, instruments used, cycle frequency, and how results are recorded.

Send what you have. We can help identify and develop the missing information.

Start a project brief ↗

Related solutions

The adjacent details matter.

A complete solution may combine several of these applications.

Your next useful step

Bring the application. We’ll help develop the solution.

Tell us what must work, what already exists, and the quantity you need. Technical and project conversations are available in English and Spanish.

Tell us what must work